jumping to kernel entry at 0xc0090000.
GDB: no debug ports present
KDB: debugger backends: ddb
KDB: current backend: ddb
Copyright (c) 1992-2011 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
	The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 10.0-CURRENT #12: Wed Dec 14 15:29:33 EST 2011
    root@aals174.au.alcatel-lucent.com:/usr/obj/usr/src/sys/GENERIC sparc64
WARNING: WITNESS option enabled, expect reduced performance.
real memory  = 68719476736 (65536 MB)
avail memory = 67261685760 (64145 MB)
cpu0: Sun Microsystems UltraSparc-IV Processor (1350.00 MHz CPU)
cpu1: Sun Microsystems UltraSparc-IV Processor (1350.00 MHz CPU)
cpu2: Sun Microsystems UltraSparc-IV Processor (1350.00 MHz CPU)
cpu3: Sun Microsystems UltraSparc-IV Processor (1350.00 MHz CPU)
cpu4: Sun Microsystems UltraSparc-IV Processor (1350.00 MHz CPU)
cpu5: Sun Microsystems UltraSparc-IV Processor (1350.00 MHz CPU)
cpu6: Sun Microsystems UltraSparc-IV Processor (1350.00 MHz CPU)
cpu7: Sun Microsystems UltraSparc-IV Processor (1350.00 MHz CPU)
cpu8: Sun Microsystems UltraSparc-IV Processor (1350.00 MHz CPU)
cpu9: Sun Microsystems UltraSparc-IV Processor (1350.00 MHz CPU)
cpu10: Sun Microsystems UltraSparc-IV Processor (1350.00 MHz CPU)
cpu11: Sun Microsystems UltraSparc-IV Processor (1350.00 MHz CPU)
cpu12: Sun Microsystems UltraSparc-IV Processor (1350.00 MHz CPU)
cpu13: Sun Microsystems UltraSparc-IV Processor (1350.00 MHz CPU)
cpu14: Sun Microsystems UltraSparc-IV Processor (1350.00 MHz CPU)
cpu15: Sun Microsystems UltraSparc-IV Processor (1350.00 MHz CPU)
FreeBSD/SMP: Multiprocessor System Detected: 16 CPUs
kbd0 at kbdmux0
nexus0: <Open Firmware Nexus device>
pcib0: <Sun Host-PCI bridge> mem 0x40004700000-0x40004717fff,0x40004410000-0x4000441004f,0x7ffee000000-0x7ffee0000ff irq 563,560,561,564,565 on nexus0
pcib0: Schizo, version 7, IGN 0x8, bus B, PCI mode, 33MHz
pcib0: DVMA map: 0xc0000000 to 0xffffffff 131072 entries, streaming buffer
pci0: <OFW PCI bus> on pcib0
pcib1: <Sun Host-PCI bridge> mem 0x40004600000-0x40004617fff,0x40004410000-0x4000441004f,0x7ffec000000-0x7ffec0000ff irq 562,560,561,564,566 on nexus0
pcib1: Schizo, version 7, IGN 0x8, bus A, PCI mode, 66MHz
Timecounter "pcib1" frequency 150000000 Hz quality 100
pcib1: DVMA map: 0xc0000000 to 0xffffffff 131072 entries, streaming buffer
pci1: <OFW PCI bus> on pcib1
pcib2: <Sun Host-PCI bridge> mem 0x40004f00000-0x40004f17fff,0x40004c10000-0x40004c1004f,0x7ffea000000-0x7ffea0000ff irq 627,624,625,628,629 on nexus0
pcib2: Schizo, version 7, IGN 0x9, bus B, PCI mode, 33MHz
pcib2: DVMA map: 0xc0000000 to 0xffffffff 131072 entries, streaming buffer
pci2: <OFW PCI bus> on pcib2
ebus0: <PCI-EBus3 bridge> mem 0x7d000000-0x7dffffff,0x7e000000-0x7e7fffff at device 1.0 on pci2
pcib3: <Sun Host-PCI bridge> mem 0x40004e00000-0x40004e17fff,0x40004c10000-0x40004c1004f,0x7ffe8000000-0x7ffe80000ff irq 626,624,625,628,630 on nexus0
pcib3: Schizo, version 7, IGN 0x9, bus A, PCI mode, 66MHz
Timecounter "pcib3" frequency 150000000 Hz quality 100
pcib3: DVMA map: 0xc0000000 to 0xffffffff 131072 entries, streaming buffer
pci3: <OFW PCI bus> on pcib3
pcib4: <OFW PCI-PCI bridge> at device 1.0 on pci3
pci4: <OFW PCI bus> on pcib4
pcib5: <OFW PCI-PCI bridge> at device 2.0 on pci3
pci5: <OFW PCI bus> on pcib5
nexus0: <memory-controller> mem 0x40000400000-0x40000400047 type memory-controller (no driver attached)
nexus0: <memory-controller> mem 0x40000c00000-0x40000c00047 type memory-controller (no driver attached)
nexus0: <memory-controller> mem 0x40001400000-0x40001400047 type memory-controller (no driver attached)
nexus0: <memory-controller> mem 0x40001c00000-0x40001c00047 type memory-controller (no driver attached)
nexus0: <memory-controller> mem 0x40002400000-0x40002400047 type memory-controller (no driver attached)
nexus0: <memory-controller> mem 0x40002c00000-0x40002c00047 type memory-controller (no driver attached)
nexus0: <memory-controller> mem 0x40003400000-0x40003400047 type memory-controller (no driver attached)
nexus0: <memory-controller> mem 0x40003c00000-0x40003c00047 type memory-controller (no driver attached)
atapci0: <SiI (CMD) 646U2 UDMA33 controller> port 0x300-0x307,0x318-0x31b,0x310-0x317,0x308-0x30b,0x320-0x32f at device 1.0 on pci0
atapci0: HW has secondary channel disabled
ata2: <ATA channel> at channel 0 on atapci0
gem0: <Sun GEM Gigabit Ethernet> mem 0x200000-0x3fffff at device 1.0 on pci1
miibus0: <MII bus> on gem0
gentbi0: <Generic ten-bit interface> PHY 0 on miibus0
gentbi0:  none, 1000baseSX, 1000baseSX-FDX, auto, auto-flow
gem0: 20kB RX FIFO, 9kB TX FIFO
gem0: Ethernet address: 00:14:4f:4a:de:8b
isp0: <Qlogic ISP 2200 PCI FC-AL Adapter> port 0x300-0x3ff mem 0x400000-0x400fff at device 2.0 on pci1
isp0: Board Type 2200, Chip Revision 0x5, loaded F/W Revision 2.2.6
isp0: 309 max I/O command limit set
isp0: invalid NVRAM header
isp0: invalid NVRAM header
isp0: Chan 0 0x400000007f000009/0x400000007f000009 Role Initiator
isp0: bad frame length (0) from NVRAM- using 1024
isp0: bad execution throttle of 0- using 16
ebus0: <flashprom> addr 0-0x1fffff (no driver attached)
ebus0: <bbc> addr 0x100000000-0x1000fffff (no driver attached)
ebus0: <power> addr 0x10030002e-0x10030002f,0x100300600-0x100300607 (no driver attached)
ebus0: <i2c> addr 0x10000002e-0x10000002f,0x10000002d irq 35 (no driver attached)
ebus0: <i2c> addr 0x100000030-0x100000031 irq 35 (no driver attached)
ebus0: <bbc> addr 0x100500000-0x1005fffff (no driver attached)
ebus0: <i2c> addr 0x10050002e-0x10050002f,0x10050002d irq 40 (no driver attached)
ebus0: <i2c> addr 0x100500030-0x100500031 irq 40 (no driver attached)
rtc0: <Real-Time Clock> addr 0x100300070-0x100300071 irq 36 on ebus0
ebus0: <gpio> addr 0x100300600-0x100300607 (no driver attached)
ebus0: <pmc> addr 0x100300700-0x100300701 (no driver attached)
uart0: <16550 or compatible> addr 0x1003062f8-0x1003062ff irq 46 on ebus0
uart1: <16550 or compatible> addr 0x1003083f8-0x1003083ff irq 45 on ebus0
uart1: console (115200,n,8,1)
scc0: <Siemens SAB 82532 dual channel SCC> addr 0x100400000-0x10040007f irq 34 on ebus0
uart2: <SAB 82532 v3.2, channel A> on scc0
uart2: CTS oflow
uart3: <SAB 82532 v3.2, channel B> on scc0
uart3: CTS oflow
gem1: <Sun ERI 10/100 Ethernet> mem 0x100000-0x11ffff at device 1.1 on pci2
miibus1: <MII bus> on gem1
ukphy0: <Generic IEEE 802.3u media interface> PHY 1 on miibus1
ukphy0:  none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto, auto-flow
gem1: 2kB RX FIFO, 2kB TX FIFO
gem1: Ethernet address: 00:14:4f:4a:de:8a
ohci0: <Sun PCIO-2 USB controller> mem 0x1000000-0x1007fff at device 1.3 on pci2
usbus0: <Sun PCIO-2 USB controller> on ohci0
isp1: <Qlogic ISP 2200 PCI FC-AL Adapter> port 0x1000-0x10ff mem 0x100000-0x100fff at device 4.0 on pci4
isp1: Board Type 2200, Chip Revision 0x5, loaded F/W Revision 2.2.6
isp1: 1024 max I/O command limit set
isp1: NVRAM Port WWN 0x210100e08b267f99
isp1: Chan 0 0x200000e08b267f99/0x210100e08b267f99 Role Initiator
isp1: Chan 0: LOOP Reset
isp2: <Qlogic ISP 2200 PCI FC-AL Adapter> port 0x1100-0x11ff mem 0x102000-0x102fff at device 5.0 on pci4
isp2: Board Type 2200, Chip Revision 0x5, loaded F/W Revision 2.2.6
isp2: 1024 max I/O command limit set
isp2: NVRAM Port WWN 0x210000e08b067f99
isp2: Chan 0 0x200000e08b067f99/0x210000e08b067f99 Role Initiator
cas0: <NS DP83065 Saturn Gigabit Ethernet> mem 0x200000-0x3fffff at device 0.0 on pci5
miibus2: <MII bus> on cas0
nsgphy0: <DP83865 1000BASE-T media interface> PHY 1 on miibus2
none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto, auto-flow
cas0: 16kB RX FIFO, 9kB TX FIFO
cas0: Ethernet address: 00:14:4f:42:c3:20
cas1: <NS DP83065 Saturn Gigabit Ethernet> mem 0x600000-0x7fffff at device 1.0 on pci5
miibus3: <MII bus> on cas1
nsgphy1: <DP83865 1000BASE-T media interface> PHY 1 on miibus3
none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto, auto-flow
cas1: 16kB RX FIFO, 9kB TX FIFO
cas1: Ethernet address: 00:14:4f:42:c3:21
cas2: <NS DP83065 Saturn Gigabit Ethernet> mem 0x800000-0x9fffff at device 2.0 on pci5
miibus4: <MII bus> on cas2
nsgphy2: <DP83865 1000BASE-T media interface> PHY 1 on miibus4
none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto, auto-flow
cas2: 16kB RX FIFO, 9kB TX FIFO
cas2: Ethernet address: 00:14:4f:42:c3:22
cas3: <NS DP83065 Saturn Gigabit Ethernet> mem 0xc00000-0xdfffff at device 3.0 on pci5
miibus5: <MII bus> on cas3
nsgphy3: <DP83865 1000BASE-T media interface> PHY 1 on miibus5
none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto, auto-flow
cas3: 16kB RX FIFO, 9kB TX FIFO
cas3: Ethernet address: 00:14:4f:42:c3:23
nexus0: <syscons> type unknown (no driver attached)
Timecounter "tick" frequency 1350000000 Hz quality 10
Timecounter "stick" frequency 10000000 Hz quality 10
Event timer "tick" frequency 1350000000 Hz quality 1000
Timecounters tick every 1.000 msec
isp0: Chan 0: LIP Received
isp1: Chan 0: LIP Received
isp0: Chan 0 Loop UP
isp1: Chan 0 Loop UP
isp0: Chan 0 Port Database Changed
isp1: Chan 0 Port Database Changed
isp0: Chan 0 Firmware State <Config Wait->Ready>
isp0: Chan 0 WWPN 0x400000007f000009 PortID 0x000029 N-Port Handle 109, Connection 'Private Loop'
isp0: Chan 0 PortID 0x0000ef handle 0x0 role Target arrived at tgt 0 WWPN 0x21000000875017a5
isp0: Chan 0 PortID 0x0000e8 handle 0x1 role Target arrived at tgt 1 WWPN 0x21000000875014ba
isp0: Chan 0 PortID 0x0000e4 handle 0x2 role Target arrived at tgt 2 WWPN 0x2100000087501828
isp0: Chan 0 PortID 0x0000e2 handle 0x3 role Target arrived at tgt 3 WWPN 0x210000008796f785
isp0: Chan 0 PortID 0x0000e1 handle 0x4 role Target arrived at tgt 4 WWPN 0x2100000087501755
isp0: Chan 0 PortID 0x0000e0 handle 0x5 role Target arrived at tgt 5 WWPN 0x2100000087505ebc
isp0: Chan 0 PortID 0x0000dc handle 0x6 role Target arrived at tgt 6 WWPN 0x508002000025a7c1
usbus0: 12Mbps Full Speed USB v1.0
isp1: Chan 0 Firmware State <Config Wait->Ready>
isp1: Chan 0 WWPN 0x210100e08b267f99 PortID 0x0000da N-Port Handle 7, Connection 'Private Loop'
isp1: Chan 0 PortID 0x0000ef handle 0x0 role Target arrived at tgt 0 WWPN 0x500000e01999c6b1
isp1: Chan 0 PortID 0x0000e8 handle 0x1 role Target arrived at tgt 1 WWPN 0x500000e01365b4e1
isp1: Chan 0 PortID 0x0000e4 handle 0x2 role Target arrived at tgt 2 WWPN 0x500000e014422a51
isp1: Chan 0 PortID 0x0000e2 handle 0x3 role Target arrived at tgt 3 WWPN 0x500000e01998e821
isp1: Chan 0 PortID 0x0000e1 handle 0x4 role Target arrived at tgt 4 WWPN 0x500000e014397bb1
isp1: Chan 0 PortID 0x0000e0 handle 0x5 role Target arrived at tgt 5 WWPN 0x500000e0143f8ee1
isp1: Chan 0 PortID 0x0000dc handle 0x6 role Target arrived at tgt 6 WWPN 0x508002000065a569
ugen0.1: <SUN> at usbus0
uhub0: <SUN OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus0
isp2: Chan 0 Firmware State <Config Wait->Loss Of Sync>
uhub0: 4 ports with 4 removable, self powered
(probe6:isp0:0:6:0): TEST UNIT READY. CDB: 0 0 0 0 0 0 
(probe6:isp0:0:6:0): CAM status: SCSI Status Error
(probe6:isp0:0:6:0): SCSI status: Check Condition
(probe6:isp0:0:6:0): SCSI sense: UNIT ATTENTION asc:29,1 (Power on occurred)
(probe518:isp1:0:6:0): TEST UNIT READY. CDB: 0 0 0 0 0 0 
(probe518:isp1:0:6:0): CAM status: SCSI Status Error
(probe518:isp1:0:6:0): SCSI status: Check Condition
(probe518:isp1:0:6:0): SCSI sense: UNIT ATTENTION asc:29,1 (Power on occurred)
isp2: Chan 0 Firmware State <Config Wait->Loss Of Sync>
isp2: Chan 0 Firmware State <Config Wait->Loss Of Sync>
da0 at isp0 bus 0 scbus1 target 0 lun 0
da0: <HITACHI HUS1014FASUN146G 2A08> Fixed Direct Access SCSI-3 device 
da0: 100.000MB/s transfers WWNN 0x20000000875017a5 WWPN 0x21000000875017a5 PortID 0xef
da0: Command Queueing enabled
da0: 140009MB (286739329 512 byte sectors: 255H 63S/T 17848C)
da6 at isp1 bus 0 scbus2 target 0 lun 0
da6: <FUJITSU MAW3147FCSUN146G 1303> Fixed Direct Access SCSI-4 device 
da6: 100.000MB/s transfers WWNN 0x500000e01999c6b0 WWPN 0x500000e01999c6b1 PortID 0xef
da6: Command Queueing enabled
da6: 140009MB (286739329 512 byte sectors: 255H 63S/T 17848C)
da7 at isp1 bus 0 scbus2 target 1 lun 0
da7: <FUJITSU MAW3147FCSUN146G 1303> Fixed Direct Access SCSI-4 device 
da7: 100.000MB/s transfers WWNN 0x500000e01365b4e0 WWPN 0x500000e01365b4e1 PortID 0xe8
da7: Command Queueing enabled
da7: 140009MB (286739329 512 byte sectors: 255H 63S/T 17848C)
da8 at isp1 bus 0 scbus2 target 2 lun 0
da8: <FUJITSU MAW3147FCSUN146G 1303> Fixed Direct Access SCSI-4 device 
da8: 100.000MB/s transfers WWNN 0x500000e014422a50 WWPN 0x500000e014422a51 PortID 0xe4
da8: Command Queueing enabled
da8: 140009MB (286739329 512 byte sectors: 255H 63S/T 17848C)
da9 at isp1 bus 0 scbus2 target 3 lun 0
da9: <FUJITSU MAW3147FCSUN146G 1303> Fixed Direct Access SCSI-4 device 
da9: 100.000MB/s transfers WWNN 0x500000e01998e820 WWPN 0x500000e01998e821 PortID 0xe2
da9: Command Queueing enabled
da9: 140009MB (286739329 512 byte sectors: 255H 63S/T 17848C)
da10 at isp1 bus 0 scbus2 target 4 lun 0
da10: <FUJITSU MAW3147FCSUN146G 1303> Fixed Direct Access SCSI-4 device 
da10: 100.000MB/s transfers WWNN 0x500000e014397bb0 WWPN 0x500000e014397bb1 PortID 0xe1
da10: Command Queueing enabled
da10: 140009MB (286739329 512 byte sectors: 255H 63S/T 17848C)
da11 at isp1 bus 0 scbus2 target 5 lun 0
da11: <FUJITSU MAW3147FCSUN146G 1303> Fixed Direct Access SCSI-4 device 
da11: 100.000MB/s transfers WWNN 0x500000e0143f8ee0 WWPN 0x500000e0143f8ee1 PortID 0xe0
da11: Command Queueing enabled
da11: 140009MB (286739329 512 byte sectors: 255H 63S/T 17848C)
da1 at isp0 bus 0 scbus1 target 1 lun 0
da1: <HITACHI HUS1014FASUN146G 2A08> Fixed Direct Access SCSI-3 device 
da1: 100.000MB/s transfers WWNN 0x20000000875014ba WWPN 0x21000000875014ba PortID 0xe8
da1: Command Queueing enabled
da1: 140009MB (286739329 512 byte sectors: 255H 63S/T 17848C)
da2 at isp0 bus 0 scbus1 target 2 lun 0
da2: <HITACHI HUS1014FASUN146G 2A08> Fixed Direct Access SCSI-3 device 
da2: 100.000MB/s transfers WWNN 0x2000000087501828 WWPN 0x2100000087501828 PortID 0xe4
da2: Command Queueing enabled
da2: 140009MB (286739329 512 byte sectors: 255H 63S/T 17848C)
da3 at isp0 bus 0 scbus1 target 3 lun 0
da3: <HITACHI HUS1014FASUN146G 2A08> Fixed Direct Access SCSI-3 device 
da3: 100.000MB/s transfers WWNN 0x200000008796f785 WWPN 0x210000008796f785 PortID 0xe2
da3: Command Queueing enabled
da3: 140009MB (286739329 512 byte sectors: 255H 63S/T 17848C)
da4 at isp0 bus 0 scbus1 target 4 lun 0
da4: <HITACHI HUS1014FASUN146G 2A08> Fixed Direct Access SCSI-3 device 
da4: 100.000MB/s transfers WWNN 0x2000000087501755 WWPN 0x2100000087501755 PortID 0xe1
da4: Command Queueing enabled
da4: 140009MB (286739329 512 byte sectors: 255H 63S/T 17848C)
da5 at isp0 bus 0 scbus1 target 5 lun 0
da5: <HITACHI HUS1014FASUN146G 2A08> Fixed Direct Access SCSI-3 device 
da5: 100.000MB/s transfers WWNN 0x2000000087505ebc WWPN 0x2100000087505ebc PortID 0xe0
da5: Command Queueing enabled
da5: 140009MB (286739329 512 byte sectors: 255H 63S/T 17848C)
ses0 at isp0 bus 0 scbus1 target 6 lun 0
ses0: <SUNW SUNWGS INT FCBPL 922A> Fixed Enclosure Services SCSI-3 device 
ses0: 100.000MB/s transfers WWNN 0x508002000025a7c0 WWPN 0x508002000025a7c1 PortID 0xdc
ses0: SCSI-3 SES Device
ses1 at isp1 bus 0 scbus2 target 6 lun 0
ses1: cd0 at ata2 bus 0 scbus0 target 0 lun 0
cd0: <TSSTcorp DVD-ROM TS-H352C SI00> Removable CD-ROM SCSI-0 device 
cd0: 33.300MB/s transfers (UDMA2, ATAPI 12bytes, PIO 65534bytes)
cd0: Attempt to query device size failed: NOT READY, Medium not present - tray closed
<SUNW SUNWGS INT FCBPL 922A> Fixed Enclosure Services SCSI-3 device 
ses1: 100.000MB/s transfers WWNN 0x508002000065a568 WWPN 0x508002000065a569 PortID 0xdc
ses1: SCSI-3 SES Device
SMP: AP CPU #1 Launched!
SMP: AP CPU #2 Launched!
SMP: AP CPU #3 Launched!
SMP: AP CPU #4 Launched!
SMP: AP CPU #5 Launched!
SMP: AP CPU #6 Launched!
SMP: AP CPU #7 Launched!
SMP: AP CPU #8 Launched!
SMP: AP CPU #9 Launched!
SMP: AP CPU #10 Launched!
SMP: AP CPU #11 Launched!
SMP: AP CPU #12 Launched!
SMP: AP CPU #13 Launched!
SMP: AP CPU #14 Launched!
SMP: AP CPU #15 Launched!
WARNING: WITNESS option enabled, expect reduced performance.
GEOM: da5: adding VTOC8 information.
Trying to mount root from ufs:/dev/da10a [rw]...
Enter full pathname of shell or RETURN for /bin/sh: 
# sysctl kern.sched
kern.sched.cpusetsize: 8
kern.sched.preemption: 1
kern.sched.runq_fuzz: 1
kern.sched.ipiwakeup.useloop: 0
kern.sched.ipiwakeup.usemask: 1
kern.sched.ipiwakeup.delivered: 4316
kern.sched.ipiwakeup.requested: 4316
kern.sched.ipiwakeup.enabled: 1
kern.sched.quantum: 100000
kern.sched.name: 4BSD
 
4bsd_dmesg.txt · Last modified: 2013/06/08 11:00 by peterjeremy
 
Recent changes RSS feed Creative Commons License Donate Powered by PHP Valid XHTML 1.0 Valid CSS Driven by DokuWiki