*jumping to kernel entry at 0xc0090000. GDB: no debug ports present KDB: debugger backends: ddb KDB: current backend: ddb Copyright (c) 1992-2011 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD is a registered trademark of The FreeBSD Foundation. FreeBSD 10.0-CURRENT #11: Mon Dec 5 08:06:05 EST 2011 root@aals174.au.alcatel-lucent.com:/usr/obj/usr/src/sys/GENERIC sparc64 WARNING: WITNESS option enabled, expect reduced performance. real memory = 68719476736 (65536 MB) avail memory = 67261685760 (64145 MB) cpu0: Sun Microsystems UltraSparc-IV Processor (1350.00 MHz CPU) cpu1: Sun Microsystems UltraSparc-IV Processor (1350.00 MHz CPU) cpu2: Sun Microsystems UltraSparc-IV Processor (1350.00 MHz CPU) cpu3: Sun Microsystems UltraSparc-IV Processor (1350.00 MHz CPU) cpu4: Sun Microsystems UltraSparc-IV Processor (1350.00 MHz CPU) cpu5: Sun Microsystems UltraSparc-IV Processor (1350.00 MHz CPU) cpu6: Sun Microsystems UltraSparc-IV Processor (1350.00 MHz CPU) cpu7: Sun Microsystems UltraSparc-IV Processor (1350.00 MHz CPU) cpu8: Sun Microsystems UltraSparc-IV Processor (1350.00 MHz CPU) cpu9: Sun Microsystems UltraSparc-IV Processor (1350.00 MHz CPU) cpu10: Sun Microsystems UltraSparc-IV Processor (1350.00 MHz CPU) cpu11: Sun Microsystems UltraSparc-IV Processor (1350.00 MHz CPU) cpu12: Sun Microsystems UltraSparc-IV Processor (1350.00 MHz CPU) cpu13: Sun Microsystems UltraSparc-IV Processor (1350.00 MHz CPU) cpu14: Sun Microsystems UltraSparc-IV Processor (1350.00 MHz CPU) cpu15: Sun Microsystems UltraSparc-IV Processor (1350.00 MHz CPU) FreeBSD/SMP: Multiprocessor System Detected: 16 CPUs kbd0 at kbdmux0 nexus0: pcib0: mem 0x40004700000-0x40004717fff,0x40004410000-0x4000441004f,0x7ffee000000-0x7ffee0000ff irq 563,560,561,564,565 on nexus0 pcib0: Schizo, version 7, IGN 0x8, bus B, PCI mode, 33MHz pcib0: DVMA map: 0xc0000000 to 0xffffffff 131072 entries, streaming buffer pci0: on pcib0 pcib1: mem 0x40004600000-0x40004617fff,0x40004410000-0x4000441004f,0x7ffec000000-0x7ffec0000ff irq 562,560,561,564,566 on nexus0 pcib1: Schizo, version 7, IGN 0x8, bus A, PCI mode, 66MHz Timecounter "pcib1" frequency 150000000 Hz quality 100 pcib1: DVMA map: 0xc0000000 to 0xffffffff 131072 entries, streaming buffer pci1: on pcib1 pcib2: mem 0x40004f00000-0x40004f17fff,0x40004c10000-0x40004c1004f,0x7ffea000000-0x7ffea0000ff irq 627,624,625,628,629 on nexus0 pcib2: Schizo, version 7, IGN 0x9, bus B, PCI mode, 33MHz pcib2: DVMA map: 0xc0000000 to 0xffffffff 131072 entries, streaming buffer pci2: on pcib2 ebus0: mem 0x7d000000-0x7dffffff,0x7e000000-0x7e7fffff at device 1.0 on pci2 pcib3: mem 0x40004e00000-0x40004e17fff,0x40004c10000-0x40004c1004f,0x7ffe8000000-0x7ffe80000ff irq 626,624,625,628,630 on nexus0 pcib3: Schizo, version 7, IGN 0x9, bus A, PCI mode, 66MHz Timecounter "pcib3" frequency 150000000 Hz quality 100 pcib3: DVMA map: 0xc0000000 to 0xffffffff 131072 entries, streaming buffer pci3: on pcib3 pcib4: at device 1.0 on pci3 pci4: on pcib4 pcib5: at device 2.0 on pci3 pci5: on pcib5 nexus0: mem 0x40000400000-0x40000400047 type memory-controller (no driver attached) nexus0: mem 0x40000c00000-0x40000c00047 type memory-controller (no driver attached) nexus0: mem 0x40001400000-0x40001400047 type memory-controller (no driver attached) nexus0: mem 0x40001c00000-0x40001c00047 type memory-controller (no driver attached) nexus0: mem 0x40002400000-0x40002400047 type memory-controller (no driver attached) nexus0: mem 0x40002c00000-0x40002c00047 type memory-controller (no driver attached) nexus0: mem 0x40003400000-0x40003400047 type memory-controller (no driver attached) nexus0: mem 0x40003c00000-0x40003c00047 type memory-controller (no driver attached) atapci0: port 0x300-0x307,0x318-0x31b,0x310-0x317,0x308-0x30b,0x320-0x32f at device 1.0 on pci0 atapci0: HW has secondary channel disabled ata2: at channel 0 on atapci0 gem0: mem 0x200000-0x3fffff at device 1.0 on pci1 miibus0: on gem0 gentbi0: PHY 0 on miibus0 gentbi0: none, 1000baseSX, 1000baseSX-FDX, auto, auto-flow gem0: 20kB RX FIFO, 9kB TX FIFO gem0: Ethernet address: 00:14:4f:4a:de:8b isp0: port 0x300-0x3ff mem 0x400000-0x400fff at device 2.0 on pci1 isp0: Board Type 2200, Chip Revision 0x5, loaded F/W Revision 2.2.6 isp0: 309 max I/O command limit set isp0: invalid NVRAM header isp0: invalid NVRAM header isp0: Chan 0 0x400000007f000009/0x400000007f000009 Role Initiator isp0: bad frame length (0) from NVRAM- using 1024 isp0: bad execution throttle of 0- using 16 ebus0: addr 0-0x1fffff (no driver attached) ebus0: addr 0x100000000-0x1000fffff (no driver attached) ebus0: addr 0x10030002e-0x10030002f,0x100300600-0x100300607 (no driver attached) ebus0: addr 0x10000002e-0x10000002f,0x10000002d irq 35 (no driver attached) ebus0: addr 0x100000030-0x100000031 irq 35 (no driver attached) ebus0: addr 0x100500000-0x1005fffff (no driver attached) ebus0: addr 0x10050002e-0x10050002f,0x10050002d irq 40 (no driver attached) ebus0: addr 0x100500030-0x100500031 irq 40 (no driver attached) rtc0: addr 0x100300070-0x100300071 irq 36 on ebus0 ebus0: addr 0x100300600-0x100300607 (no driver attached) ebus0: addr 0x100300700-0x100300701 (no driver attached) uart0: <16550 or compatible> addr 0x1003062f8-0x1003062ff irq 46 on ebus0 uart1: <16550 or compatible> addr 0x1003083f8-0x1003083ff irq 45 on ebus0 uart1: console (115200,n,8,1) scc0: addr 0x100400000-0x10040007f irq 34 on ebus0 uart2: on scc0 uart2: CTS oflow uart3: on scc0 uart3: CTS oflow gem1: mem 0x100000-0x11ffff at device 1.1 on pci2 miibus1: on gem1 ukphy0: PHY 1 on miibus1 ukphy0: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto, auto-flow gem1: 2kB RX FIFO, 2kB TX FIFO gem1: Ethernet address: 00:14:4f:4a:de:8a ohci0: mem 0x1000000-0x1007fff at device 1.3 on pci2 usbus0: on ohci0 isp1: port 0x1000-0x10ff mem 0x100000-0x100fff at device 4.0 on pci4 isp1: Board Type 2200, Chip Revision 0x5, loaded F/W Revision 2.2.6 isp1: 1024 max I/O command limit set isp1: NVRAM Port WWN 0x210100e08b267f99 isp1: Chan 0 0x200000e08b267f99/0x210100e08b267f99 Role Initiator isp1: Chan 0: LOOP Reset isp2: port 0x1100-0x11ff mem 0x102000-0x102fff at device 5.0 on pci4 isp2: Board Type 2200, Chip Revision 0x5, loaded F/W Revision 2.2.6 isp2: 1024 max I/O command limit set isp2: NVRAM Port WWN 0x210000e08b067f99 isp2: Chan 0 0x200000e08b067f99/0x210000e08b067f99 Role Initiator cas0: mem 0x200000-0x3fffff at device 0.0 on pci5 miibus2: on cas0 nsgphy0: PHY 1 on miibus2 none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto, auto-flow cas0: 16kB RX FIFO, 9kB TX FIFO cas0: Ethernet address: 00:14:4f:42:c3:20 cas1: mem 0x600000-0x7fffff at device 1.0 on pci5 miibus3: on cas1 nsgphy1: PHY 1 on miibus3 none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto, auto-flow cas1: 16kB RX FIFO, 9kB TX FIFO cas1: Ethernet address: 00:14:4f:42:c3:21 cas2: mem 0x800000-0x9fffff at device 2.0 on pci5 miibus4: on cas2 nsgphy2: PHY 1 on miibus4 none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto, auto-flow cas2: 16kB RX FIFO, 9kB TX FIFO cas2: Ethernet address: 00:14:4f:42:c3:22 cas3: mem 0xc00000-0xdfffff at device 3.0 on pci5 miibus5: on cas3 nsgphy3: PHY 1 on miibus5 none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-master, 1000baseT-FDX, 1000baseT-FDX-master, auto, auto-flow cas3: 16kB RX FIFO, 9kB TX FIFO cas3: Ethernet address: 00:14:4f:42:c3:23 nexus0: type unknown (no driver attached) Timecounter "tick" frequency 1350000000 Hz quality 10 Timecounter "stick" frequency 10000000 Hz quality 10 Event timer "tick" frequency 1350000000 Hz quality 1000 Timecounters tick every 1.000 msec isp0: Chan 0: LIP Received isp1: Chan 0: LIP Received isp0: Chan 0 Loop UP isp1: Chan 0 Loop UP isp0: Chan 0 Port Database Changed isp1: Chan 0 Port Database Changed isp0: Chan 0 Firmware State Ready> isp0: Chan 0 WWPN 0x400000007f000009 PortID 0x000029 N-Port Handle 109, Connection 'Private Loop' isp0: Chan 0 PortID 0x0000ef handle 0x0 role Target arrived at tgt 0 WWPN 0x21000000875017a5 isp0: Chan 0 PortID 0x0000e8 handle 0x1 role Target arrived at tgt 1 WWPN 0x21000000875014ba isp0: Chan 0 PortID 0x0000e4 handle 0x2 role Target arrived at tgt 2 WWPN 0x2100000087501828 isp0: Chan 0 PortID 0x0000e2 handle 0x3 role Target arrived at tgt 3 WWPN 0x210000008796f785 isp0: Chan 0 PortID 0x0000e1 handle 0x4 role Target arrived at tgt 4 WWPN 0x2100000087501755 isp0: Chan 0 PortID 0x0000e0 handle 0x5 role Target arrived at tgt 5 WWPN 0x2100000087505ebc isp0: Chan 0 PortID 0x0000dc handle 0x6 role Target arrived at tgt 6 WWPN 0x508002000025a7c1 usbus0: 12Mbps Full Speed USB v1.0 isp1: Chan 0 Firmware State Ready> isp1: Chan 0 WWPN 0x210100e08b267f99 PortID 0x0000da N-Port Handle 7, Connection 'Private Loop' isp1: Chan 0 PortID 0x0000ef handle 0x0 role Target arrived at tgt 0 WWPN 0x500000e01999c6b1 isp1: Chan 0 PortID 0x0000e8 handle 0x1 role Target arrived at tgt 1 WWPN 0x500000e01365b4e1 isp1: Chan 0 PortID 0x0000e4 handle 0x2 role Target arrived at tgt 2 WWPN 0x500000e014422a51 isp1: Chan 0 PortID 0x0000e2 handle 0x3 role Target arrived at tgt 3 WWPN 0x500000e01998e821 isp1: Chan 0 PortID 0x0000e1 handle 0x4 role Target arrived at tgt 4 WWPN 0x500000e014397bb1 isp1: Chan 0 PortID 0x0000e0 handle 0x5 role Target arrived at tgt 5 WWPN 0x500000e0143f8ee1 isp1: Chan 0 PortID 0x0000dc handle 0x6 role Target arrived at tgt 6 WWPN 0x508002000065a569 ugen0.1: at usbus0 uhub0: on usbus0 isp2: Chan 0 Firmware State Loss Of Sync> uhub0: 4 ports with 4 removable, self powered (probe6:isp0:0:6:0): TEST UNIT READY. CDB: 0 0 0 0 0 0 (probe6:isp0:0:6:0): CAM status: SCSI Status Error (probe6:isp0:0:6:0): SCSI status: Check Condition (probe6:isp0:0:6:0): SCSI sense: UNIT ATTENTION asc:29,1 (Power on occurred) (probe518:isp1:0:6:0): TEST UNIT READY. CDB: 0 0 0 0 0 0 (probe518:isp1:0:6:0): CAM status: SCSI Status Error (probe518:isp1:0:6:0): SCSI status: Check Condition (probe518:isp1:0:6:0): SCSI sense: UNIT ATTENTION asc:29,1 (Power on occurred) isp2: Chan 0 Firmware State Loss Of Sync> isp2: Chan 0 Firmware State Loss Of Sync> da0 at isp0 bus 0 scbus1 target 0 lun 0 da0: Fixed Direct Access SCSI-3 device da0: 100.000MB/s transfers WWNN 0x20000000875017a5 WWPN 0x21000000875017a5 PortID 0xef da0: Command Queueing enabled da0: 140009MB (286739329 512 byte sectors: 255H 63S/T 17848C) da6 at isp1 bus 0 scbus2 target 0 lun 0 da6: Fixed Direct Access SCSI-4 device da6: 100.000MB/s transfers WWNN 0x500000e01999c6b0 WWPN 0x500000e01999c6b1 PortID 0xef da6: Command Queueing enabled da6: 140009MB (286739329 512 byte sectors: 255H 63S/T 17848C) da7 at isp1 bus 0 scbus2 target 1 lun 0 da7: Fixed Direct Access SCSI-4 device da7: 100.000MB/s transfers WWNN 0x500000e01365b4e0 WWPN 0x500000e01365b4e1 PortID 0xe8 da7: Command Queueing enabled da7: 140009MB (286739329 512 byte sectors: 255H 63S/T 17848C) da8 at isp1 bus 0 scbus2 target 2 lun 0 da8: Fixed Direct Access SCSI-4 device da8: 100.000MB/s transfers WWNN 0x500000e014422a50 WWPN 0x500000e014422a51 PortID 0xe4 da8: Command Queueing enabled da8: 140009MB (286739329 512 byte sectors: 255H 63S/T 17848C) da9 at isp1 bus 0 scbus2 target 3 lun 0 da9: Fixed Direct Access SCSI-4 device da9: 100.000MB/s transfers WWNN 0x500000e01998e820 WWPN 0x500000e01998e821 PortID 0xe2 da9: Command Queueing enabled da9: 140009MB (286739329 512 byte sectors: 255H 63S/T 17848C) da10 at isp1 bus 0 scbus2 target 4 lun 0 da10: Fixed Direct Access SCSI-4 device da10: 100.000MB/s transfers WWNN 0x500000e014397bb0 WWPN 0x500000e014397bb1 PortID 0xe1 da10: Command Queueing enabled da10: 140009MB (286739329 512 byte sectors: 255H 63S/T 17848C) da11 at isp1 bus 0 scbus2 target 5 lun 0 da11: Fixed Direct Access SCSI-4 device da11: 100.000MB/s transfers WWNN 0x500000e0143f8ee0 WWPN 0x500000e0143f8ee1 PortID 0xe0 da11: Command Queueing enabled da11: 140009MB (286739329 512 byte sectors: 255H 63S/T 17848C) da2 at isp0 bus 0 scbus1 target 2 lun 0 da2: Fixed Direct Access SCSI-3 device da2: 100.000MB/s transfers WWNN 0x2000000087501828 WWPN 0x2100000087501828 PortID 0xe4 da2: Command Queueing enabled da2: 140009MB (286739329 512 byte sectors: 255H 63S/T 17848C) da1 at isp0 bus 0 scbus1 target 1 lun 0 da1: Fixed Direct Access SCSI-3 device da1: 100.000MB/s transfers WWNN 0x20000000875014ba WWPN 0x21000000875014ba PortID 0xe8 da1: Command Queueing enabled da1: 140009MB (286739329 512 byte sectors: 255H 63S/T 17848C) da3 at isp0 bus 0 scbus1 target 3 lun 0 da3: Fixed Direct Access SCSI-3 device da3: 100.000MB/s transfers WWNN 0x200000008796f785 WWPN 0x210000008796f785 PortID 0xe2 da3: Command Queueing enabled da3: 140009MB (286739329 512 byte sectors: 255H 63S/T 17848C) da4 at isp0 bus 0 scbus1 target 4 lun 0 da4: Fixed Direct Access SCSI-3 device da4: 100.000MB/s transfers WWNN 0x2000000087501755 WWPN 0x2100000087501755 PortID 0xe1 da4: Command Queueing enabled da4: 140009MB (286739329 512 byte sectors: 255H 63S/T 17848C) da5 at isp0 bus 0 scbus1 target 5 lun 0 da5: Fixed Direct Access SCSI-3 device da5: 100.000MB/s transfers WWNN 0x2000000087505ebc WWPN 0x2100000087505ebc PortID 0xe0 da5: Command Queueing enabled da5: 140009MB (286739329 512 byte sectors: 255H 63S/T 17848C) ses0 at isp0 bus 0 scbus1 target 6 lun 0 ses0: Fixed Enclosure Services SCSI-3 device ses0: 100.000MB/s transfers WWNN 0x508002000025a7c0 WWPN 0x508002000025a7c1 PortID 0xdc ses0: SCSI-3 SES Device ses1 at isp1 bus 0 scbus2 target 6 lun 0 ses1: cd0 at ata2 bus 0 scbus0 target 0 lun 0 cd0: Removable CD-ROM SCSI-0 device cd0: 33.300MB/s transfers (UDMA2, ATAPI 12bytes, PIO 65534bytes) cd0: Attempt to query device size failed: NOT READY, Medium not present - tray closed Fixed Enclosure Services SCSI-3 device ses1: 100.000MB/s transfers WWNN 0x508002000065a568 WWPN 0x508002000065a569 PortID 0xdc ses1: SCSI-3 SES Device SMP: AP CPU #1 Launched! SMP: AP CPU #2 Launched! SMP: AP CPU #3 Launched! SMP: AP CPU #4 Launched! SMP: AP CPU #5 Launched! SMP: AP CPU #6 Launched! SMP: AP CPU #7 Launched! SMP: AP CPU #8 Launched! SMP: AP CPU #9 Launched! SMP: AP CPU #10 Launched! SMP: AP CPU #11 Launched! SMP: AP CPU #12 Launched! SMP: AP CPU #13 Launched! SMP: AP CPU #14 Launched! SMP: AP CPU #15 Launched! WARNING: WITNESS option enabled, expect reduced performance. GEOM: da5: adding VTOC8 information. Trying to mount root from ufs:/dev/da10a [rw]... Enter full pathname of shell or RETURN for /bin/sh: # sysctl kern.sched kern.sched.cpusetsize: 8 kern.sched.preemption: 1 kern.sched.topology_spec: 0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15 kern.sched.steal_thresh: 3 kern.sched.steal_idle: 1 kern.sched.steal_htt: 1 kern.sched.balance_interval: 127 kern.sched.balance: 1 kern.sched.affinity: 1 kern.sched.idlespinthresh: 16 kern.sched.idlespins: 10000 kern.sched.static_boost: 152 kern.sched.preempt_thresh: 80 kern.sched.interact: 30 kern.sched.slice: 12 kern.sched.name: ULE